CONFEDERATE NAVAL CUTLASS.

Brass guard and grip with scale design, anchor on the pommel and marked CSN. Leather and brass sheath. Marked Palmetto Armoury 1861. Condition: believed to be a preproduction.

REPLICA CIVIL WAR CONFEDERATE NAVAL CUTLASS, solid brass hilt resembling that of the M1841 US Naval cutlass with fishscale grip, D-guard, and drop quillon, front of the pommel is cast "CSN"

Rare American Civil War era Confederate Navy Cutlass ~ Naval Short Sword. Total length (inside scabbard if present) : 21 3/4", Blade length : 16 1/2". ~~ DEAR BIDDERS, Please View More Detailed Close-

Confederate Naval Knife or Dirk, double edged blade, with ricasso stamped Winchester on one side, possibly made by Simon Dodge of Winchester, VA. Turned walnut grip with a flat iron disk at the top. H

AUSTRIAN MODEL 1858 NAVAL CUTLASS BOARDING SWORD Austro-Hungarian Navy Cutlass Boarding Sword. Heavy pipe-back, straight, quill-point blade. 1.5" width at ricasso. Various maker / proof marks on the g

Naval Cutlass W/ Leather Scabbard. Size: 32 1/2 x 5 in.

Stamped at ricasso: Ames Mfg. Co., Chicopee, Mass. // [anchor] 1861; and 867 on the guard. Condition: blade good; grip with crack and some losses to leather, copper coil missing; some denting to cup.

marked "N.P. Ames, Cabotville, Mass, U.S.N. 1842," Federal Eagle on each side of pommel, quintillion broken off, 21 in. blade, no scabbard, no fullers

Scarce Ames Civil War naval cutlass with solid riveted brass hand guard stamped with number 32. Blade is stamped 1862 and Ames Mfg Co. Chicopee Mass. 26 in blade, overall 32 in. Grip is leather-wrappe

U.S. Model 1841 Naval Cutlass, Nathaniel P. Ames, Springfield, Massachusetts, 1843. Cast brass hilt with wide counter-guard, quillon marked 'JCB,' the tapering knuckle bow connecting to the eagle deco

U.S. Model 1860 Naval Cutlass. Marked at the ricasso "U.S.N. / D P / 1863. Measures 32" Long with 26" Blade. The Larry Mangus Collection, Corinth, Mississippi. Condition - Overall good condition with

Blade end stamped 1862 USN DR and on verso Made by Ames Mfg. Co. Some wear to the guard. No scabbard. Overall approx. 32" long.

Reference: The American Sword 1775-1945, Harold Leslie Peterson, page 54, figure 53. Condition: very good Length: 32" Ca. 1860

Single-edged blade engraved on the spine, "Manuf're R'ale de Chatellerault 9'bre 1837" (manufactured royal of Chatellerault September 1837), stamped on ricasso with correct inspection stamps (poinç

US Naval cutlass manufactured by the Ames Manufacturing Company. Marked "N.P. Ames Cabotville Mass." for Nathan P. Ames Jr. (1803-1847), one of the founders of the company, on the blade near

Heading: (Civil War - Confederate States of America) Author: Barksdale, E. and James Lyons Title: Report from the Joint Select Committee to Investigate the Management of the Navy Department. Place Pub

Heavy steel bowl guard with fixing for the bayonet bar. The blade is slightly curved, the blade of this particular bayonet is marked with a maker’s mark of a CK / C in a shield-like cartouche.

Signed and dated in the ricasso, 32 inches long (overall)

US Naval cutlass manufactured by the Ames Manufacturing Company. Marked "N.P. Ames Cabotville Mass." for Nathan P. Ames Jr. (1803-1847), one of the founders of the company, on the blade near

32" LONG, LEATHER SCABBARD IS A BIT SCUFFED

Attic Condition M1860 Ames Naval Cutlass24-7/8 in. single fuller blade, its 1862 date barely visible, other markings are obliterated by pitting; a brass guard surrounds the wooden grip. 30-3/4 in. ove

A pair of 1859 pattern naval cutlass bayonets A pair of 1859 pattern naval cutlass bayonets, with leather grips, lacking scabbards, blade 68cm long total 82.5cm long Condition Report: Considerable wea

32" LONG

AMES 1862 NAVAL CUTLASS Ames M1860 Naval Cutlass, 32" long overall, the ricasso marked: "USN D.R. 1862", wire on grip a bit loose but leather fully intact, hand guard fine. Tip of sword bears a little