Edelbrock Intake with 2-2 Barrel Carbs.

Set up for 6 2 barrel Carburetors, marked C 67, appears to have never been used, good condition

In very good overall condition. Shows minor wear throughout. No noted cracks or repairs. Someone marked it 5405. It displays very well. 7.5"x21 7.8"

Intake Manifold, Edelbrock, for 1932-48 Ford Flathead w/4 Stromberg 97-2 bbl carbs, aluminum, Rare, Exc cond, untested.

Tri Power Intake Manifold for Y-Block Ford, 292/312, Edelbrock 553, alum w/(2) Ford 94 Model 59's on ends & (1) 94 1 1/16 ECG6 center carb, has linkage & lines, Serial #485604086, appears in Good unte

Tri Power Intake Manifold for Y-Block Ford, 292/312, Edelbrock 553 alum w/(2) Ford 94 Model 59's on ends & (1) unmarked 94 center carb, has linkage & lines, appears in Good cond, untested.

The stack is marked Harrell. The intake is unmarked. It shows light wear throughout. No noted cracks or repairs. It displays very well and is a unique intake. 7 3/8"x21 7/8"

Was painted at one point. Marked F-7975. Shows wear and paint loss throughout. No noted cracks or repairs. Displays well and the carbs mount on an angle. 7.5"x21 7/8"

Marked PM-7. Shows some wear throughout with some nicks and chips. Has a very old repair which can be seen from the top and bottom. Displays well. 7.5"x21.75"

Shows some wear and paint loss throughout. Was painted at some point. No noted cracks or repairs. Displays well. 7.25"x21 5/8"

Nice overall condition. Shows light wear and some nicks throughout. No noted cracks or repairs. Displays well. 7 3/8"x21.5"

Marked 047M on the bottom. Very nice overall condition. Shows light wear and some nicks. No noted cracks or repairs. Displays well. 7 3/8"x21.75"

Shows some wear throughout. Dirty but will clean up nice. Has a couple chips on the front. No noted cracks or repairs. 7 3/8"x22 1/8"

Shows minor wear throughout. Marked ER2. Dirty but will clean up nice. No noted cracks or repairs. Displays well. 7.5"x21.25"

Shows light wear throughout. Dirty but will clean up nice. No noted cracks or repairs. Displays well. 7.5"x21 1/8"

Shows some wear throughout. Dirty but will clean up nice. No noted cracks or repairs. Displays well. 7.5"x21.25"

Shows light wear throughout. The collar around one hole has a small chip and there is a screw in it. No noted cracks or repairs. Displays well. 7.5"x21"

Shows some minor wear throughout. No noted cracks or repairs. Displays well. 7.25"x21 5/8"

Has not been drilled. Has Battersby wrote on it in marker. Possible recast. Shows very little wear and is rough cast. No noted cracks or repairs. Displays well. 7 3/8"x21 3/8"

Has Cragar wrote on it in marker. Shows sear throughout. Dirty but will clean up. No noted cracks or repairs. Displays well. 5.5"x12 1/8"

For model A & B. Shows some wear and scratching throughout. No noted cracks or repairs. Has Evans wrote on it in marker. Displays well. 5.5"x12 1/8"

Very hard to find early intake. Shows minor wear, some small nicks, and a small chip along the bottom edge. We have not tried to remove the fittings. Needs to be cleaned. No noted cracks or repairs. D

Marked MFG. By Electric & Carburetor Eng. Co Los Angeles. Also marked T4726. Shows paint loss and minor wear throughout. Has chip on one end. Dirty but will clean up nice. No noted cracks or repai

Intake Manifold, new Ford Flathead 1948-53, single manifold, aluminum #C8BA-C8RT 6520 w/gear drive "slingshot" 2-carb adapter, has 97 Stromberg & clone carb, Exc cond, untested.

Speed Equipment (5), Thickston 2 carb air cleaner holder, Speed Products (Vintage Speed SP101) Gas Pedal, 4 bbl Ram intake & untested 8K Sun tach & Bat-O-Meter, Exc cond.