Large Exhibition Standard Overtype Stationary Steam Engine,

Large Stationary Steam Engine by Doll, c. 1935 Nuremberg, no. 520/4, fixed cylinder, length of the boiler 12 ¼ in., Ø 4 in., boiler support, 2 boiler galleries with stairs and railings, two

Large stationary steam engine model hand built and mounted into a wood box display. Apparently unmarked. Approximate height 9.5", width 15.6", depth 9".

Bertoia BASICS Online: BING #13675 LOCO OVERTYPE STATIONARY STEAM ENGINE circa 1902, burnished engine, boiler, wooden base, beveled firebox, water level glass, whistle, pressure valve, speed control,

Earl example with fancy tile floor mounted to 16.5 X 7.5” wood base. Includes burner, dynamo with switch & night. Base shows some staining in center, otherwise presents well. Very Good.

Working Model of a Stationary Single-Cylinder Overtype Steam Engine, c. 1960 Extremely detailed engineering model, brass, steel and cast iron, gas-fired, brass boiler, 7/8 in. cylinder, attached chimn

Large Working Model of a Stationary Twin-Cylinder Undertype Steam Engine, c. 1975 Extremely detailed model, brass, steel and cast-iron parts, partly finished in green, coal-fired, soldered brass flame

American. 1900s. Cast iron, brass, copper. Used as a salesman sample. Maker unknown. 8.5" x 10" x 6".

Twin cylinder overtype; smallest in the model 502 series of three; cast iron firebox with 3 vents. Original brick type stack. Fairly elaborate with ladders and platforms, twin flywheels, etc. Conditio

A MODEL VERTICAL OVERHEAD CRANK STATIONARY STEAM ENGINE, 20TH CENTURY, the heavily cast and machined 6-spoke flywheel fitted to one end of the overhead crankshaft, supported by a pierced cast plate an

Stationary Steam Engine by Doll, c. 1927 Nuremberg, no. 510/3, fixed cylinder, length of the boiler 11 in., Ø 3 1/2 in., 2 boiler galleries with railings, with water level gauge, safety valve, st

Has a great look, cylinder is free and wheel spins freely, has oiler, shows some wear and paint loss, displays well, not marked, mounted on a slab of wood, heavy, 17.75"x25", rated 8

Cast iron, steel and brass model of a large single cylinder engine. Signed. Height 8 1/2 inches. Note: Arnold Edmund Thompson (1931-2010) Marblehead, MA. In the early 1950's during his USAF tour he pe

Large steam engine piston drive with flywheel, on oak base, brass & steel, base is 23.5" by 11", height is 8.75", steam engines, machine accessories

Includes original wooden box marked 1 only 4F steam engine, with label on one end. Original box is missing top sliding piece. Engine itself is horizontal with original red stack. Condition: (Excellent

This is a very cool rarer c1935 Marklin stationary steam engine. It is model 4097/6 and appears complete and original WITH ORIGINAL BURNER AND FUNNEL. 15" tall x 12" x 12". Tried to test it and it's m

Nice early example dampfmaschine with tin tile floor mounted on 11 X 9.5” wood base. It includes its burner and scarce filler cup, just missing the streetlamp whistle. It would benefit from a cleani

Unusual form on embossed litho support mounted to cast iron base, 9 X 5.5:. Shine brass boiler with burner and screened stash. This will polish nicely. Excellent.

Doll et Cie German Toy Steam Engine. Worn from use. Dusty. Missing stack.

Nice original condition but needs cleaning; burner missing. Condition: (Very Good - Excellent). Dimensions: 12" x 5" x 12 - 3/4".

Bertoia BASICS Online: J F JOS FALK OVERTYPE STEAM ENGINE circa 1925 Base 10" x 5" x 14" h.

Dimensions: 5.5" H x 6.5" W Shipping is the buyer's responsibility! We recommend obtaining a quote from a third party shipper prior to bidding

Brass & Steel with cast iron base, 6” square. It appears intact and complete, minus burner. Shows light playwear. From the Clint Miller Collection.

Bertoia BASICS Online: ERNEST PLANK OVERTYPE STEAM ENGINE circa 1930 Base 6" x 3 1/2" x 8" h.

Impressive working model of a double cylinder overtype steam engine, mounted on a checkerboard decorated base, with two ladders that give access to open catwalk, a fully functional governor, pressure