Steam Locomotive Bell 11.5" Diameter, Acorn Finial., complete with Yoke

A very heavy steam locomotive bell with an 11 1/2" diameter and 9" height to the base casting. Overall with yoke it is 21" tall. Mounted on a rolling base. No casting marks or shop stamped numbers on

The brass or bronze bell with red interior and measuring 12 7/8 inches at the widest point is suspended in an iron yoke and cradle on circular base with iron crank and acorn finial at the top, unmarke

12" diameter x 18.5" tall with cast yoke and acorn finial

12" bell diameter. The case yoke is 20" tall with acorn finial.

A large steam locomotive bell. It has a 17" diameter and the actual bell is 12" high. The cast iron yoke has 2 casting marks: base has 65697 (note "5" is upside down), top has 24139. I did find any sh

Excellent example with yoke and acorn finial. 16" bell diameter with 32" tall. Double oilers or greasers

Brass 6" diameter with 12 1/2" chamber length. Acorn finial, no markings. It is mounted on a wooden base with room for another whistle on the stand. The whole unit stands about 23" tall. The control a

A large and heavy steam locomotive bell. It has a 17" diameter and it measures 12" high with a total height of 14" to the top of the mounting fitting. The cast iron yoke measures 17" bottom to top whe

Older steam locomotive bell with 2 concentric rings on the bottom edge. The cast Iron yoke has some casting marks that are hard to read. This bell does not have any shop stamps. Including the rolling

12" bell diameter. The cast yoke 19-1/2" tall. Lehigh Valley Steam Locomotive Bell. Pat. Pending

All brass medium size bell off a fire engine. Bell diameter is 17" tall including yoke and acorn finial. Nice

10" Diameter Brass Steam Locomotive Bell Bell measures 10" in diameter with an acorn top nut. The yolk has been repainted and appears to have MD 227 cast in near the bottom. The bottom plate is curved

A 16" cast bronze steam locomotive bell mounted in a very heavy cast iron yoke with a hex nut finial. There appears to be provisions for an air ringer on the lever side. Clapper is intact. Bell shows

Nice condition Antique steam locomotive 12" bell with cast iron yoke. The bell measures 12" in diameter x 10" tall, the yoke measures 25" tall x 18" across and is maked 26421 & 4956.

Antique steam locomotive 16-1/2" bell with cast iron yoke. The bell measures 16-1/2" in diameter x 14" tall, the yoke measures 32" tall x 24-1/2" across overall.

Provenance unknown, but came from Northwestern United States and resembles Northern Pacific RR whistles of that time period. 5" diameter shroud, replaced valve and a nicely repaired acorn finial. Fits

Canadian. 1920s. Brass. Original and correct acorn finial. Stamped, "Jas Morrison Brass Co. Ltd., Toronto" upper bell. Horseless Carriage Museum, Fenelon Falls, Ont. 19"H x 4" bell diameter.

Steam Locomotive bell with cast iron yoke. Bell measures 14" high and base diameter of 16". Wonderful tone when rung. These bells ae always made of an alloy specific to bells, designed to provide that

A Lunkenheimer bronze three-chime whistle. The bell measures 6" in diameter and 23" tall to the top of the acorn finial. There is no valve hardware. It is mounted on a 5 - 1/2" pipe flange for display

A heavy little bel with 12" diameter. It also stands 9" on the bell height. With the yoke it measures 25" tall. It mounts flat (not a curved boiler). It is probably from a gas car or electric locomoti

Brass steam whistle. 3" diameter, 6" tube height, 13 1/2" total height. Piston does move on valve..

A very heavy steam locomotive bell with (15" diameter and 12" base to top dimensions. Mounted on a rolling base. Air ringer is untested. Loads of shop stamped numbers on top, please see the pics. You

14 1/2" Diameter Brass steam locomotive bell. The bell is polished brass with a repainted red interior. Equipped with a Trans Devices ringer. The bell itself is otherwise unmarked. The yolk has 12 V S

DESCRIPTION: Large Howard steam locomotive bell. Brass bell with cast iron yoke and crank. Embossed with "Howard" to top and bottom of yoke. Howard produced bells for steam engines form 1840 onward. F