Howard 12" Diameter Brass Locomotive Bell

14 1/2" Diameter Brass steam locomotive bell. The bell is polished brass with a repainted red interior. Equipped with a Trans Devices ringer. The bell itself is otherwise unmarked. The yolk has 12 V S

A heavy little bel with 12" diameter. It also stands 9" on the bell height. With the yoke it measures 25" tall. It mounts flat (not a curved boiler). It is probably from a gas car or electric locomoti

12" diameter x 18.5" tall with cast yoke and acorn finial

12" diameter x 18.5" tall in triangular yoke

12" bell diameter. The case yoke is 20" tall with acorn finial.

Railroad bell is air powered. Bell is approx 12" in diameter and 10 3/4" tall. It is mounted on a rolling stand. No shipping.

11" diameter x 12" high. Unmarked. IMPORTANT: Before bidding, please read the terms and conditions below. When you registered for the auction you agreed to these terms and will be required to comply w

A flat mount bell that measures 9" high by 12" diameter. Bells in general are not brass or bronze but a "bell" metal that is a mixture of metals. The total height with yoke is 22". One side arm has a

Brass Air Powered Diesel Locomotive Bell - 12 3/4" diameter Bell is equipped with a Graham White double acting ringer. Bell shows minor dents and wear at the edge, but no major damage. The mount appea

Look past the paint! The yoke has HOWARD cast twice: once up top and larger on the base. The bell measures 9" high by 12" diameter. The total height with yoke is 19". It has both a pull arm and a air

12" bell diameter. The cast yoke 19-1/2" tall. Lehigh Valley Steam Locomotive Bell. Pat. Pending

The brass or bronze bell with red interior and measuring 12 7/8 inches at the widest point is suspended in an iron yoke and cradle on circular base with iron crank and acorn finial at the top, unmarke

Brass Locomotive Bell - 10 1/4" diameter Brass Locomotive Bell - 10 1/4" diameter. The base has two mounting holes and a slight curvature to the base which would have allowed it to sit flush against a

10" Diameter Brass Steam Locomotive Bell Bell measures 10" in diameter with an acorn top nut. The yolk has been repainted and appears to have MD 227 cast in near the bottom. The bottom plate is curved

Howard 8" Diameter Brass Bell Bell measures 8" in diameter and is marked with Howard on the yoke and base. Base measures 5 1/4" by 8 1/2" and is flat with no curvature.

12"dia. brass locomotive or fire engine bell -Good

DESCRIPTION: Large Howard steam locomotive bell. Brass bell with cast iron yoke and crank. Embossed with "Howard" to top and bottom of yoke. Howard produced bells for steam engines form 1840 onward. F

Older steam locomotive bell with 2 concentric rings on the bottom edge. The cast Iron yoke has some casting marks that are hard to read. This bell does not have any shop stamps. Including the rolling

BRASS SHIP'S BELLMarked “D Noyes 1915”.Height 12”. Diameter 12”.

A very heavy steam locomotive bell with (15" diameter and 12" base to top dimensions. Mounted on a rolling base. Air ringer is untested. Loads of shop stamped numbers on top, please see the pics. You

Cast iron back plate with brass bell. The bell is 12" diameter. Complete with bracket. Nice

Very nice early brass locomotive bell. Matching brass finial. Cast iron cradle and yolk made by Howard. Interior repainted red. Condition (Excellent). Size 19 -1/2" T.

Solid piece, no markings, red painted bell interior, 25 inches tall, 16 inch bell diameter, no shipping due to weight Line Item # 67

Very nice early brass locomotive bell. Cradle and yolk made by Howard. Interior repainted red. Condition (Excellent). Size 21 -1/2" T.