* Howard Locomotive Bell 9" by 12" with Yoke

Look past the paint! The yoke has HOWARD cast twice: once up top and larger on the base. The bell measures 9" high by 12" diameter. The total height with yoke is 19". It has both a pull arm and a air

A flat mount bell that measures 9" high by 12" diameter. Bells in general are not brass or bronze but a "bell" metal that is a mixture of metals. The total height with yoke is 22". One side arm has a

A heavy little bel with 12" diameter. It also stands 9" on the bell height. With the yoke it measures 25" tall. It mounts flat (not a curved boiler). It is probably from a gas car or electric locomoti

Nice condition Antique steam locomotive 12" bell with cast iron yoke. The bell measures 12" in diameter x 10" tall, the yoke measures 25" tall x 18" across and is maked 26421 & 4956.

DESCRIPTION: Large Howard steam locomotive bell. Brass bell with cast iron yoke and crank. Embossed with "Howard" to top and bottom of yoke. Howard produced bells for steam engines form 1840 onward. F

Older steam locomotive bell with 2 concentric rings on the bottom edge. The cast Iron yoke has some casting marks that are hard to read. This bell does not have any shop stamps. Including the rolling

A large steam locomotive bell. It has a 17" diameter and the actual bell is 12" high. The cast iron yoke has 2 casting marks: base has 65697 (note "5" is upside down), top has 24139. I did find any sh

12" bell diameter. The case yoke is 20" tall with acorn finial.

This bronze bell is air-powered (pneumatic) for locomotive use. It measures 9 in. high and 12 in. in diameter with a piston driven clapper. No maker identification. Compressed air moves the clapper at

12" bell diameter. The cast yoke 19-1/2" tall. Lehigh Valley Steam Locomotive Bell. Pat. Pending

The brass or bronze bell with red interior and measuring 12 7/8 inches at the widest point is suspended in an iron yoke and cradle on circular base with iron crank and acorn finial at the top, unmarke

A large and heavy steam locomotive bell. It has a 17" diameter and it measures 12" high with a total height of 14" to the top of the mounting fitting. The cast iron yoke measures 17" bottom to top whe

12" diameter x 18.5" tall with cast yoke and acorn finial

A very heavy steam locomotive bell with an 11 1/2" diameter and 9" height to the base casting. Overall with yoke it is 21" tall. Mounted on a rolling base. No casting marks or shop stamped numbers on

12" diameter x 18.5" tall in triangular yoke

Cast Iron Bell from O.S. Bell & Co. Hillsboro O. #1 Upright Bell, 1886. Bell is approx. 13 3/4" in diameter, and 9"high (12" high with mount and swing arm). Yoke is 18" wide and 16" tall. NOTE- Heavy/

Brass Air Powered Diesel Locomotive Bell - 12 3/4" diameter Bell is equipped with a Graham White double acting ringer. Bell shows minor dents and wear at the edge, but no major damage. The mount appea

San Francisco Trolley Bell. Circa 1930s. Brass stamped “Muni RY”. Diameter of bell 9 ½”. Light oxidation to fastener, without pull-chain, else near fine.

Drypoint etching signed Alistair Bell, #9/12, 7" x 10 1/2", "Horn Bill".

Steam Locomotive bell with cast iron yoke. Bell measures 14" high and base diameter of 16". Wonderful tone when rung. These bells ae always made of an alloy specific to bells, designed to provide that

Antique steam locomotive 16-1/2" bell with cast iron yoke. The bell measures 16-1/2" in diameter x 14" tall, the yoke measures 32" tall x 24-1/2" across overall.

Two Ship's Bells, 10" x 9 1/2".

A Bronze Locomotive Bell united states, circa 1900 15" W x 12" D x 18" H Estimate $500-700

Tray 5 Mid East Brass Vases 10 1/2", 9 1/2", 7" + Bell