Solid Brass Ships Clinometer on Board

Vintage Solid Brass Ships Clinometer / Inclinometer

Solid brass ships bell mounted to a mahogany board with carved rope border. With mounting yoke and clanger.

Ship Aft Wheel-Hyde Windlass Co. Bath, ME, USA, Solid brass stand, Cast Iron Wheel with wooden handles, solid brass turret. Mounted on hardwood board.

Solid copper waterproof ship's flare canister with brass badge reading "Coston Distress Outfit, for lifeboats and rafts, approved by the U.S. Board Supervising Inspectors. Coston Supply Co. Inc. New Y

16" Solid Brass Ships Bell, El Rio Brass Bell with custom-made stand, Ship was built in 1899, sunk by collision in 1942

Solid Brass Ship's Wheel on Stanchion, marked "John Hastie & Co. Ltd., Engineers, Greenock (England)" with degree declination arrow indicator, the wheel having 8 spokes, 42" diam. 52" tall overall, 33

Ship's bridge telegraph with twin faces displaying ship's commands. Highly polished and electrified to light its face up brightly. The successful bidder will have the option of removing this item fro

Highly polished ships course telegraph with makers plate from Bendix. Faceplate shows course commands including hard left, steady, course,anf right, from zero to thirty five degrees.

Highly polished brass ships bridge telegraph. English. With ships commands full, half, slow, dead slow, finished with engines, stop, astern and ahead. 42"H x 14"Dia x 9"Deep 56 lbs.

"Mariner Yacht Wheel", s/n 238035, mounted on a molded mahogany plate base and backing, 3 1/2" dial, retaining the original brass winding key. Label verso from Lewis & Son, The Master Watchmakers, One

Ship's porthole converted to a mahogany side table that has a lower shelf fashioned as ship's grating. Solid brass porthole with hinged port secured with two dogbolts. Dimensions: 23" (height) x 19 1/

Highly polished ships porthole with lacquer finish mounted to a custom bar height table with ship grating shelf below. Shelf has floor guards. Hinged glass port. Dimension: 42 H” x 24 L” 6

Porthole comes from the ocean liner "Homeric", formerly the "Mariposa". The heavy porthole is of the "flower pattern". Base is mahogany with ship's grating shelf. Dimensions: 27" H (with handle) x 24"

Antique solid brass ship's bell with turned brass exterior. Heavy clanger. Dimensions: 12" H x 10" diameter Weight: 27lbs

This is a very nice solid brass ships anchor in the classic configuration. The anchor does have a brass rod that is attached to the top which swivels. The anchor measures 32 inches tall, 20 inches wid

With three glass panels. Solid mahogany base. Wood handle. Electric socket with Edison bulb has been fitted to the original burner for home enjoyment. 12 LBS 17" H x 13" L x 8" D wood base

Twenty-eight-inch solid brass six spoke ships wheel with lacquer finish. Sizeable hub with keyway. 28 LBS 28" Diame.

Solid brass boat lantern with clear, red, and blue lenses. Hinged rear door and vented top. Two carry handles on rear. Burner inside. Dimensions: 8 tall by 8 wide by 5 deep.

Solid Brass Ships Port Hole mounted on wood

Shps engine room telegraph by Joseph Harper and Son of New York. Polished faceplate with ship commands. This model would be mounted in the engine room and rings very loudly because of the high level o

Highly polished ships anchor lantern with carry and bail handles, fresnel glass lens, mounted to a thick solid mahogany base that is wired with electricity for home use.

Solid brass ship's throttle and gear assembly from a yacht. Three levers rise from the heavy brass housing. To a mahogany base with rope carving. Quite heavy. Face is 7" diameter x 13" overall height

Inside lid states "Shipbuilders Great Lakes Engineering Works, Detroit". Brass ship's porthole from an unknown Great Lakes freighter. Roughness on one spot on glass but very good condition. Body is br

Highly polished boat binnacle with gimballed compass by "Star" of Boston. Sidelight is fitted with oil burner. Mounted to a sturdy wood base. Weight is 11 pounds. 13" H x 8" Diameter without base 13"