11 1/2" Diameter Brass Steam Locomotive Bell & Cradle

14 1/2" Diameter Brass steam locomotive bell. The bell is polished brass with a repainted red interior. Equipped with a Trans Devices ringer. The bell itself is otherwise unmarked. The yolk has 12 V S

11" diameter x 12" high. Unmarked. IMPORTANT: Before bidding, please read the terms and conditions below. When you registered for the auction you agreed to these terms and will be required to comply w

12" bell diameter. The cast yoke 19-1/2" tall. Lehigh Valley Steam Locomotive Bell. Pat. Pending

Three Chime Brass Steam Locomotive Whistle Whistle measures 11 1/4" tall with a 4" diameter bell. The inlet size is 1 3/4". The bell has an 1 1/2" shallow dent near the top and other minor areas of pi

The brass or bronze bell with red interior and measuring 12 7/8 inches at the widest point is suspended in an iron yoke and cradle on circular base with iron crank and acorn finial at the top, unmarke

10" Diameter Brass Steam Locomotive Bell Bell measures 10" in diameter with an acorn top nut. The yolk has been repainted and appears to have MD 227 cast in near the bottom. The bottom plate is curved

A heavy little bel with 12" diameter. It also stands 9" on the bell height. With the yoke it measures 25" tall. It mounts flat (not a curved boiler). It is probably from a gas car or electric locomoti

Older steam locomotive bell with 2 concentric rings on the bottom edge. The cast Iron yoke has some casting marks that are hard to read. This bell does not have any shop stamps. Including the rolling

12" diameter x 18.5" tall with cast yoke and acorn finial

12" diameter x 18.5" tall in triangular yoke

A very heavy steam locomotive bell with (15" diameter and 12" base to top dimensions. Mounted on a rolling base. Air ringer is untested. Loads of shop stamped numbers on top, please see the pics. You

12" bell diameter. The case yoke is 20" tall with acorn finial.

A large steam locomotive bell. It has a 17" diameter and the actual bell is 12" high. The cast iron yoke has 2 casting marks: base has 65697 (note "5" is upside down), top has 24139. I did find any sh

Railroad bell is air powered. Bell is approx 12" in diameter and 10 3/4" tall. It is mounted on a rolling stand. No shipping.

Nice condition Antique steam locomotive 12" bell with cast iron yoke. The bell measures 12" in diameter x 10" tall, the yoke measures 25" tall x 18" across and is maked 26421 & 4956.

A very heavy steam locomotive bell with an 11 1/2" diameter and 9" height to the base casting. Overall with yoke it is 21" tall. Mounted on a rolling base. No casting marks or shop stamped numbers on

A 19th century steam locomotives brass bell, bearing stamped marks #1116, measuring 15" h x 16" diameter, minor loss to rim, raised upon a later octagonal shaped wooden base, with pendant. Overall wei

Brass 6" diameter with 12 1/2" chamber length. Acorn finial, no markings. It is mounted on a wooden base with room for another whistle on the stand. The whole unit stands about 23" tall. The control a

A large and heavy steam locomotive bell. It has a 17" diameter and it measures 12" high with a total height of 14" to the top of the mounting fitting. The cast iron yoke measures 17" bottom to top whe

11" diameter x 12.75" tall. Mounted on board and bracket. Two casting chips on bottom edge

A flat mount bell that measures 9" high by 12" diameter. Bells in general are not brass or bronze but a "bell" metal that is a mixture of metals. The total height with yoke is 22". One side arm has a

Brass Air Powered Diesel Locomotive Bell - 12 3/4" diameter Bell is equipped with a Graham White double acting ringer. Bell shows minor dents and wear at the edge, but no major damage. The mount appea

Train steam generated bronze bell. Marked "Graham White" on the clapper. Marked "8004156" on the crown 12 " diameter. 16" height including bracket.

From a New York Central "Pacific" 4-6-0 #805 Steam Locomotive. 16.5" diameter x 23" tall. Called a Ten Wheeler, built 1905-1908