SCUBA TANK WITH WEIGHT BELT

Lot features one commercial hard hat style weight belt, a yellow scuba diver style belt and two curved style spare lead weights. Please refer to photos for condition details. All items will be shipped

This is a grouping of vintage scuba diving equipment, all in used condition. The gear includes a homemade weight belt with four lead ingots with brass buckle and fancy knots attached, a NCG gas regula

Scuba Divers Gear, includes: U.S. Divers Co Aqua Lung - Master - two stage regulators; Saba pro pneumatic pressure gauge; air tank; three US Divers Co. belts; WW II inflatable life belt; two masks, ja

Vintage divers weight belt in used condition. Belt has six lead weights attached and one loose with brass loop and leather strap attached. The leather surface is flaking due to age and use. Lead ingot

4 OMS OCEAN MANAGEMENT SYSTEMS STEEL FABER ITALY COMPRESSED AIR SCUBA TANKS-STAMPED ITALY30" OVERALL HEIGHT WITH VALVE-28" TO TOP OF TANK W OUT VALVE-7" DIAMETER-GOOD PRE OWNED CONDITION-DP11822

This is a very old divers weight belt with a total of eight lead weights. The belt itself is very heavy leather with brass hardware. The leather is in well used condition, brass buckles are in good co

Heavy 50-pound weight belt with 11 separate lead ingots. Belt itself is heavy old leather in well-worn condition. Please refer to photos for condition details. All items will be shipped with a signatu

Used original leather divers weight belt. This example was used for display purposes which is why painted wood blocks are in place of the lead weights. The belt has 10 wood block weights install. Belt

This is a vintage divers weight belt. It is made of leather with 8 lead ingots attached. The lead weights are not marked. There is no jockstrap. The total weight is approximately 70 pounds. Please see

This is a well-used vintage weight belt. Leather belt, 9 lead weights and rope make up this piece of equipment. Likely used by commercial diver and probably not comfortable with the rope for shoulder

Grouping of brass weight belt hardware along with twelve bolt drive dress collar. The brass hardware is for securing lead weight to the leather belt. There are 8 brass plates, two of which are stamped

Harley Davidson Flaming Gas Tank Belt Buckle. This unused metal belt buckle is approximately 5" x 1/4" x 3" and weighs 0.45lb. The belt buckle has no known damage.

Waterlung Sport Diver Scuba Tank

DESCRIPTION: 1964 G.I. Joe Action Sailor Scuba Tanks set item # 7606. CONDITION: Mint on card.

DESCRIPTION: 1964 G.I. Joe Action Sailor Scuba Tanks set item # 7606. CONDITION: Mint on card.

Milk tank: Weight approximately: 180 g Width about: 12 cm height approximately: 10 cm

This is a pair of A.J. Morse divers lead chest weights. These were used by commercial divers rather than the weight belt. Both have the Morse name. One is missing the top two brass rings. We are unsur

Unsigned Surrealist Modernist Oil Painting. Goldfish with scuba tank and gear. Landscape with crescent moon & flying saucer.-- Dimensions: H: 30.25 inches: W: 24 inches ---

This is likely a one of kind US Navy Mark V divers dress! For decades a US Navy Seal owned this dress, which also had a Mark V helmet, boots and weight belt attached to it. This canvas suit is covered

Considered the Cadillac of Scuba equipment, this is a very nice original Scott Hydro-Pac single cylinder scuba tank and backpack. The original green paint on both the bank and backpack are in wonderfu

Untested . Original box, includes scuba tank, and instructions. For 12 inch action figure, not included

Grouping of five vintage scuba tank pressure gauges. The grouping consists of a Healthways, Aqua Lung, Seacraft Industries, Voit, and one by an unknown manufacturer. Excellent collectible condition, a

Grouping of six vintage scuba tank pressure gauges. The grouping consists of a Healthways, two U.S. Divers, one with Aqua-Lung logo and other with West Pico Blvd address, AMF Voit, DACOR, and one by a

This lot consists of a nicely detailed US Navy Mark V diving helmet plaque and two Schrader hard chalk replicas of a weight belt ingots. The helmet plaque measures 6.5 inches tall and 4.25 inches wide