Queen Cutlery Schatt & Morgan 0342SK Knife

Queen Cutlery, Schatt and Morgan English Barlow #97 Folding Knife - Stag handles - Schatt and Morgan Bolsters with the bottom of the M being overground - Queen DFC Spear Blade that the tip sits on top

Count: 6 Dimensions: (Display case) H 2" x W 17.75" x D 13" Condition: No issues to note.

Includes: -(5) Queen Cutlery knives: 1 of 100 #01 Traditional Pocket, #29 jack knife, (2) 3L Mountain Man, Schatt & Morgan Reversed Peanut -(1) Utica Cutlery Co: Trapper Largest: 3.75 In blade Con

Delrin handles - Nickel silver bolsters with what appears to be a steel pin - not sure that schatt and morgan blades were put into anything but high quality handles, this was probably an old queen fra

Includes: -(5) Schatt & Morgan knives: Congress limited edition 1 of 600, Congress, Peanut, (2) Jack, Clip point folder -Longest: 4.5 In blade -Condition: all are excellent w/ boxes Provenance: A

.

Handcrafted. USA, # 26. In original box.

Plastic or Case Imitation Stag Handles - Big Q stamp - Great looking blade with swedge on one side - 13-3/4" long when shut

Wood handles - blade off center towards mark side - no wobble, good snap - blade tip was oversharpened on one end - 3-1/8" long when shut - gap between spring/liner

Wood Handles - Nickel Silver Bolsters - Blade Centered well, has slight blade rap - D2 Steel Blades - Gaps in liners/backsprings - 4-1/4" long when shut

QUEEN CUTLERY FIXED BLADE HUNTING KNIFE W/SHEATH. THE ETCHING IS LIGHT QUEEN CUTLERY TITUSVILLE PA. BLADE IS ALMOST MIRROR LIKE. TIP IS NEEDLE LIKE. NO CRACKS OR CHIPS IN THE STAG. COMES WITH ITS ORIG

Simulated Stag - gap between liner/backspring - Brass shield - good snap - off center main blade

Amber Bonestag Handles - Brass Queen Shield - Blade is proud when closed, slightly off center - light wobble, great snap - 3-3/4" long when shut

Red Micarta Handles - good snap, light play when closed - 3-5/8" long when shut

Stag handles - Very Thick knife that is 3/4" thick overall - Lined Bolsters - no wobble, good snap - 3-7/8" long when shut

Stag Handles, very thick, 7/8" thick - blade sits a little low in the galley, may have some slight slight blade rap, I can't tell - Half stop isnt very crisp, no wobble - 3-3/4" long when shut

Stag handles - slightly off center blade - light wobble, good snap - slight blade rap on close - small gap between liners and backspring - Steel Bolsters - visible eye on the pins in bolster - 3-1/2"

Amber Stag Handles - Nickel Silver Oar Carver Shield - Blade Centered well - no wobble, good snap - D2 Tool Steel Blade - These were a Special Factory Order, quite rare.

Buffalo Horn Handles - slight gap at backspring/liner - Blade centered nicely - no wobble, good snap - Bolsters appear to be overground and you can see eyes from the pins

Wood Handles - blade centered well - good snap, nice lockup - gap between backspring/liner - 4-1/2" long when shut

Amber Bonestag handles - blade centered, good snap, no wobble - gap between backspring/liner - no shield - nice knife

Amber Bonestag Handles - D2 Steel - slight wobble, great snap

Moore Maker 5202 Trapper - Buffalo Horn Handles - Good Snap - No Wobble - Gap in liner and backspring - Blades are Centered - Brass Centerpin with Nickel Silver Scale Pins - Eyes are shown from the pi

Wood Handles - gap in between backspring/liner - blade is centered - light play when in lock position - easy to close, good snap - D2 Steel